ALINOVA/Contractor Calculators and Estimating Tools
CONTRACTOR / 01

Take the guesswork out of estimates.

Calculate roof pitch, angles, deck area, board counts and material budget with fast tools for on-site planning.

MODULE 01 / 03LOCAL TOOL

Roof pitch calculator

Enter vertical rise and horizontal run in the same measurement unit, e.g. inches. Pitch displays rise per 12 units of run.

Roof pitch—
Slope angle—
Percent grade—
Slope length factor—
MODULE 02 / 03LOCAL TOOL

Deck material estimator

Estimate boards using overall deck dimensions and an assumed 12-foot board length.

Deck area—
12-foot boards—
Linear footage—
Board budget—
MORE ESTIMATORS

Concrete volume & bag calculator

Estimate slab volume, cubic yards, ready-mix cost or the equivalent number of 80 lb bags.

MODULE 03 / 03LOCAL TOOL

Concrete slab estimator

Material estimate

Cubic yards incl. waste—
Cubic feet incl. waste—
Approx. 80 lb bags—
Ready-mix material cost—

A typical 80 lb bag yields approximately 0.6 ft³. Actual yield varies by product. This is a material estimate, not structural or engineering advice.

NEW / FOCUSED TOOLS

Choose a specific tool

Direct, bookmarkable pages with their own inputs, explanations and exports.

How to use these toolsPractical examples, tips and answers — expand when needed

What is roof pitch?

Roof pitch is expressed as rise over 12 units of horizontal run. For example, 6:12 is a rise of six inches for every 12 horizontal inches. The slope length factor can help estimate distances measured along the sloped roof.

How accurate is the deck estimate?

This preliminary budgeting tool uses a simple board-width model and a 12-foot assumed board length. It does not account for support structures, fasteners, complex geometry, grading or municipal building codes. Always verify measurements and obtain professional specifications.

PRACTICAL GUIDE / ALINOVA

Work through an estimate before buying materials

Early measurements are useful for rough budgets, but they are not structural calculations or a substitute for professional plans. Keep units consistent, record assumptions and verify the actual product dimensions.

01 / GUIDE

Example: calculate a 6:12 roof pitch

If the roof rises 6 inches over 12 horizontal inches, enter rise 6 and run 12. The calculator shows a 6:12 pitch, an angle of about 26.6 degrees and a slope factor of about 1.118. This slope factor is useful for rough calculations of roof-plane length from horizontal distance. Real roofs may include hips, valleys, eaves and overhangs not represented by a single pitch.

02 / GUIDE

Example: start a deck materials budget

A rectangular 12 × 16 foot deck has a basic surface area of 192 square feet. Enter the deck dimensions, face width of the proposed boards, your gap and waste allowance, and a per-board price. The estimator assumes boards are 12 feet long and uses a simplified width-based material model. Check the actual board layout, cut lengths and stock availability before ordering; orientation and seams can change the total.

03 / GUIDE

Include waste and project exclusions

A waste allowance can cover some offcuts, but not every irregular design. The calculator does not include joists, beams, posts, footings, flashing, fasteners, railings, labor or delivery. Mark those items separately rather than interpreting the materials subtotal as a complete construction quote. The exported CSV is a working estimate, not a signed bid or an engineered plan.

04 / GUIDE

Check site conditions and safety requirements

Actual work should use measured dimensions, manufacturer installation guidelines and applicable local building permits or codes. Roof work has fall hazards; structural members must be sized for loads by a qualified professional where required. If the project is complex, irregular or safety-critical, have the dimensions and specifications reviewed before construction.

Frequently asked questions

Can I mix feet and inches in the roof calculator?

Rise and run must use the same unit. The displayed pitch normalizes the rise to 12 units of horizontal run.

Is the deck board count exact?

No. It is a simplified rough estimate using 12-foot boards; cut patterns, board direction and framing constraints can change quantities.

Does the CSV include labor and permits?

No. The CSV contains the basic material assumptions and calculated results, and should be supplemented before it is used as a quote.

ALINOVA · TOOL STUDIO

Built for real everyday tasks

Simple tools designed for desktop and mobile.

01 / ROOFS

Pitch and slope

Understand pitch, degrees and slope length before building an estimate.

02 / DECKS

Material quantities

Estimate coverage and board costs, with an adjustable waste allowance.

03 / DOCUMENTS

Download estimates

Export the material breakdown to a spreadsheet-friendly CSV file.